淮北附近有没有服务

Hello, welcome to the stainless steel water tank manufacturer!

National hotline

eighteen billion six hundred and thirty-seven million three hundred and two thousand and ninety-nine

Your location: home page > News Center > Company news

Stainless steel water tank is made of stainless steel stamping into standard block, assembled on site, and fastened by argon arc welding or bolt

Release date: June 20, 2020 Number of visits: five hundred and eighty-three

Stainless steel water tank is made of stainless steel stamping into standard block, assembled on site, and fastened by argon arc welding or bolt. It has the characteristics of non-corrosion and anti-aging, which can improve the cleanliness of water and prolong the service life of water tank. It also ensures the sanitation of domestic water and meets the requirements of environmental protection.

Products with a volume of 1-100 cubic meters are fixed products. Users can also make length, width and height according to the volume of the water tank.

characteristic

1. No rusting: stainless steel is used for food, with strong corrosion resistance.

The water tank is made of 2 / 3 light weight steel to meet the requirements of the stamping process.

3. Ideal mechanical structure: from the mechanical point of view, the convex part of the double tank is a sphere.

4. No leakage: unique structural design, all welded field combination. It has high strength, good sealing and can prevent secondary pollution of water quality.

5. Any combination, simple insulation structure: users can put forward the design requirements for any combination of length, width and height of water tank (standard plate size is 1m * 1m, 1m * 0.5m, 0.5m * 0.5m), and there is no special requirement on the installation site. Insulation services are available.

 Stainless steel water tank

Construction preparation

1. Before construction, you should be familiar with construction drawings and relevant materials. Construction drawings of water tanks shall be checked using structural and architectural drawings. You should be familiar with the water tank process, understand the construction and acceptance criteria, and prepare the construction plan.

2. Before construction, the power supply on the construction site should be implemented. Construction electricity should be negotiated with the construction unit, but it should meet the work requirements.

3. The construction site should be neat, dry and well ventilated.

4. The strip foundation of water tank shall meet the drawing and installation requirements, the height shall not be less than 300 mm, and the foundation height error shall not be more than 5 mm.

5. The construction site will be equipped with special personnel to manage the construction team and supervise the quality of water tank.

When the water level of the stainless steel water tank reaches the control line, the float will actively block the water inlet pipe

1. Install floating ball at the entrance of stainless steel water tank. When your water level reaches the control line, the float will actively block the inlet pipe, so that water can not be injected from the inlet.

2. Install electronic water level switch (controller). After the water level is detected by the built-in electron probe, the chip detects the detected signal. When the presence of water is determined, the chip outputs a high level of 24 V or 5 v. When it is determined that there is no water, the chip outputs 0V. The bump level signal is read by PLC or other control circuits and drives electrical appliances such as water pumps. The product can be installed in a comfortable direction. When the horizontal device is installed, the water level reaches the blue line with high precision. When the product is installed vertically, the water level will reach the red line and has the anti wave function.

Technical requirements of stainless steel water tank

1. Stainless steel water tank welding, material: the following are the technical parameters based on stamping stainless steel water tank. The water tank accessories are made of ordinary carbon steel plate and type, and welded with lb304ni8.0 welding rod. The quality should be different from the current standard. Rules for structural steel and carbon steel electrodes.

The lb304 stainless steel plate at the top of the box body is spliced, and the box body wall and the bottom of the box body are all butt welded (the top plate is I-type weld, the bottom plate and side wall are V-shaped welds), and other welds are fillet welds, and welding between the welds is not allowed. The cross is inserted and does not overlap with the reinforcing rib. The welding machine is lb-2-300 stainless steel water tank special welding machine, with the function of electric welding and argon welding.

2. Full water test

After the tank is manufactured, the tank is completely filled with water. After 2 to 3 hours, tap a hammer weighing 0.5 to 1.5 kg along the side of the weld about 150 mm. Leakage is acceptable. If there is water leakage, start welding from the beginning and then test.


Copyright? 2020 stainless steel manufacturer Engine technology network

Scan and consult wechat customer service
eighteen billion six hundred and thirty-seven million three hundred and two thousand and ninety-nine