淮北附近有没有服务

Hello, welcome to the stainless steel water tank manufacturer!

National hotline

eighteen billion six hundred and thirty-seven million three hundred and two thousand and ninety-nine

Your location: home page > News Center > Company news

What kind of pipes and accessories should be set in stainless steel water tank?

Release date: May 6, 2020 Number of visits: four hundred and forty-three

  Stainless steel water tank The raw materials must be of food grade and have relatively high corrosion resistance. Because the selection of raw materials is excellent, it is not only crack resistant but also corrosion-resistant. It is mainly made of ferrite, austenite and other plates with excellent performance, which has unique crack resistance and corrosion resistance.

 

The stainless steel water tank is not only durable but also very hygienic, because the whole system is closed. The stainless steel material is relatively smooth on the surface, and the algae are not easy to adhere to it. Even if there is a large amount of sediment in the water, it is convenient to clean it. The splicing type stainless steel water tank uses a 50cm polyurethane foam film on the insulation layer, so the whole system is protected The effect of temperature is very good, which belongs to the best water tank material on the market. In the installation is also more convenient, it can be arbitrarily combined and installed, because the splicing type stainless steel water tank uses the unit rectangular stainless steel forming sheet, so when splicing and assembling, it can be designed according to the installation site of the equipment, and can arbitrarily carry out the combination of polygon and ladder type.

 

Water inlet pipe: when the water tank is fed by the outdoor water supply pipe, in order to prevent overflow, the water level control valve, such as hydraulic valve and ball valve, should be installed on the water inlet pipe. The number of floating ball valves should not be less than 2. The distance between the inlet of inlet pipe and the tank cover should meet the installation requirements of floating ball valve. The diameter of inlet pipe should be determined according to the designed flow rate per second. When the water tank is supplied by the water pump and the water pump is automatically opened and closed, the water level control valve shall not be set, and the diameter of the water inlet pipe shall be determined according to the water output of the pump.

 Stainless steel water tank  

Outlet pipe: connected from the side wall of water tank. The distance from the bottom of the pipe to the bottom of the water tank shall not be less than 50 mm to prevent the sediment from flowing into the water distribution network. The pipe diameter should be determined according to the designed flow rate per second.



Overflow pipe: the orifice of overflow pipe shall be set above the allowable maximum water level of water tank, and the diameter of overflow pipe shall be determined according to the maximum inflow of water tank, generally one size larger than that of inlet pipe. Valve is not allowed on overflow pipe. In order to prevent water pollution, the overflow pipe outlet should be set with a net cover, and should not be directly connected with the drainage pipe.



Drain pipe: the drain pipe is installed at the bottom of the tank to empty the water tank during maintenance and cleaning. The pipe diameter is generally about 50 mm, and the valve shall be set on the pipe. After connecting with the overflow pipe, the same pipe can be used for drainage, but it shall not be directly connected with the drainage pipe.

 

Water level signal device: to reflect the water level control valve failure alarm device. The automatic liquid level signal meter can be used in the water tank, or a signal pipe can be set 10 mm below the overflow pipe to directly connect to the washing basin in the duty room, and the pipe diameter is generally 15-20 mm. If you need to know the water level of the water tank at any time, you can also install a liquid level meter at the side wall of the water tank for easy observation.

 

Vent pipe: when the water storage capacity of domestic water tank is large, vent pipe should be set on the cover plate of water tank to ensure regular air circulation inside the water tank. The diameter of the pipe is generally not less than 50 mm, the opening should be downward, and a net cover for mosquito prevention should be set.

 

Maintenance manhole: the manhole is mainly used for repairing water tank and inlet ball valve. Therefore, the manhole should be located on the side close to the inlet pipe. The main piping and accessories of the pool are similar to the water tank.

 


Copyright? 2020 stainless steel manufacturer Engine technology network

Scan and consult wechat customer service
eighteen billion six hundred and thirty-seven million three hundred and two thousand and ninety-nine